Skip to main content

Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

next product image
previous product image
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02
Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02

Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

  • Features & Specifications:
  •  
    • Planar technology helps reduce emissions
    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 
     
  •  
  • Compatibility:
  •  
  • 2002 Infiniti G20 2.0L 2002-2004 Infiniti I35 3.5L 2001 Nissan Altima 2.4L 2002-2004 Nissan Altima 3.5L 2002-2004 Nissan Frontier 2.4L 2002-2003 Nissan Maxima 3.5L 2001 Nissan Sentra 1.8L 2002-2004 Nissan Xterra 2.4L
  •  
  •  
    		•
    Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

    Features & Specifications:

     

    • Planar technology helps reduce emissions

    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 

     

     

    Compatibility:

     

    2002 Infiniti G20 2.0L
    2002-2004 Infiniti I35 3.5L
    2001 Nissan Altima 2.4L
    2002-2004 Nissan Altima 3.5L
    2002-2004 Nissan Frontier 2.4L
    2002-2003 Nissan Maxima 3.5L
    2001 Nissan Sentra 1.8L
    2002-2004 Nissan Xterra 2.4L

     

     

    location:Upstream: location is between the catalytic converter and the engine

                  Downstream: location is between the catalytic converter and the tailpipe

    Oxygen Sensor Q & A

    1.How are the oxygen sensors identified on a scan tool?
    When displayed on a scan tool, the right and left upstream oxygen sensors are typically labeled Bank 1, Sensor 1 and Bank 2, Sensor 1. The Bank 1 sensor will always be on the same side of a V6 or V8 engine as cylinder number one.
    On a scan tool, the downstream sensor on a four or straight six cylinder engine with single exhaust is typically labeled Bank 1, Sensor 2. On a V6, V8 or V10 engine, the downstream O2 sensor might be labeled Bank 1 or Bank 2, Sensor 2. If a V6, V8 or V10 engine has dual exhausts with dual converters, the downstream O2 sensors would be labeled Bank 1, Sensor 2 and Bank 2, Sensor 2. Or, the downstream oxygen sensor might be labeled Bank 1 Sensor 3 if the engine has two upstream oxygen sensors in the exhaust manifold (some do to more accurately monitor emissions).
    It's important to know how the O2 sensors are identified because a diagnostic trouble code that indicates a faulty O2 sensor requires a specific sensor to be replaced. Bank 1 Sensor 1 might be the back O2 sensor on a transverse V6, or it might be the one on the front exhaust manifold. What's more, the O2 sensors on a transverse engine might be labeled differently than those on a rear-wheel drive application. There is not a lot of consistency as from one vehicle manufacturer to another as to how O2 sensors are labeled, so always refer to the OEM service literature to find out which sensor is Bank 1 Sensor 1 and which one is Bank 2 Sensor 1. This information can be difficult to find. Some OEMs clearly identify which O2 sensor is which but others do not. If in doubt, call a dealer and ask somebody in the service department.

     

    2.What's the difference between a "heated" and "unheated" oxygen sensor?
    Heated oxygen sensors have an internal heater circuit that brings the sensor up to operating temperature more quickly than an unheated sensor. An oxygen sensor must be hot (about 600 to 650 degrees F) before it will generate a voltage signal. The hot exhaust from the engine will provide enough heat to bring an O2 sensor up to operating temperature, but it make take several minutes depending on ambient temperature, engine load and speed. During this time, the fuel feedback control system remains in "open loop" and does not use the O2 sensor signal to adjust the fuel mixture. This typically results in a rich fuel mixture, wasted fuel and higher emissions.
    By adding an internal heater circuit to the oxygen sensor, voltage can be routed through the heater as soon as the engine starts to warm up the sensor. The heater element is a resistor that glows red hot when current passes through it. The heater will bring the sensor up to operating temperature within 20 to 60 seconds depending on the sensor, and also keep the oxygen sensor hot even when the engine is idling for a long period of time.
    Heated O2 sensors typically have two-three or four wires (the extra wires are for the heater circuit). Note: Replacement O2 sensors must have the same number of wires as the original, and have the same internal resistance.
    The OBD II system also monitors the heater circuit and will set a trouble code if the heater circuit inside the O2 sensor is defective. The heater is part of the sensor and cannot be replaced separately, so if the heater circuit is open or shorted and the problem is not in the external wiring or sensor connector, the O2 sensor must be replaced.

     

    Sweet Tips:
    1. If you are not sure the compatibility with your car, please timely contact us! We'll check and confirm the accurate and direct fitment info for you!
    2. If the items can not work with your car after installation, please timely contact us! we would provide our professional knowledge or exchange a new item.
    3. If you are not satisfied with our product or the order. please don't make a hesitate feedback straightly, please timely contact us via eBay message! We surely provide a solution for you within 24hours!
    We sincerely hope your support and understanding! 

     

     

     


    Item Specifics
    Manufacturer Part Number AP050760A1C18
    Brand Autopartsclub2018
    Manufacturer Warranty 1 Year
    Type Sensor
    Number of Pieces 1
    Interchange Part Number 234-3113C
    Other Part Number 13968-C
    Superseded Part Number 15340CW
    Custom Bundle No
    Fitment Type Direct Replacement
    Modified Item No
    Position Upstream
    Connector Gender Male
    Wire Harness Length(mm) 450
    Wire Quantity 3
    Pin Quantity 3
    Sensor Type Heated
    Thread Diameter 18mm
    Universal Or Specific Fit Specific
    Attachment Method Screw-On
    Terminal Type Blade
    Features Direct Fit
    Type Sensor
    Features Direct Fit

    Payment

    We accept paypal only

    We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    Shipping

    1. Items will be shipped within 24 hours after getting your verified payment.

    US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim

    Returns

    1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.

    2.Any returning or exchanging item must be in new condition and cannot be tempered.

    3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.

    4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.

    Contact Us

    We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)

    Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.

    Picture
    Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

    Features & Specifications:

     

    • Planar technology helps reduce emissions

    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 

     

     

    Compatibility:

     

    2002 Infiniti G20 2.0L
    2002-2004 Infiniti I35 3.5L
    2001 Nissan Altima 2.4L
    2002-2004 Nissan Altima 3.5L
    2002-2004 Nissan Frontier 2.4L
    2002-2003 Nissan Maxima 3.5L
    2001 Nissan Sentra 1.8L
    2002-2004 Nissan Xterra 2.4L

     

     

    location:Upstream: location is between the catalytic converter and the engine

                  Downstream: location is between the catalytic converter and the tailpipe

    Oxygen Sensor Q & A

    1.How are the oxygen sensors identified on a scan tool?
    When displayed on a scan tool, the right and left upstream oxygen sensors are typically labeled Bank 1, Sensor 1 and Bank 2, Sensor 1. The Bank 1 sensor will always be on the same side of a V6 or V8 engine as cylinder number one.
    On a scan tool, the downstream sensor on a four or straight six cylinder engine with single exhaust is typically labeled Bank 1, Sensor 2. On a V6, V8 or V10 engine, the downstream O2 sensor might be labeled Bank 1 or Bank 2, Sensor 2. If a V6, V8 or V10 engine has dual exhausts with dual converters, the downstream O2 sensors would be labeled Bank 1, Sensor 2 and Bank 2, Sensor 2. Or, the downstream oxygen sensor might be labeled Bank 1 Sensor 3 if the engine has two upstream oxygen sensors in the exhaust manifold (some do to more accurately monitor emissions).
    It's important to know how the O2 sensors are identified because a diagnostic trouble code that indicates a faulty O2 sensor requires a specific sensor to be replaced. Bank 1 Sensor 1 might be the back O2 sensor on a transverse V6, or it might be the one on the front exhaust manifold. What's more, the O2 sensors on a transverse engine might be labeled differently than those on a rear-wheel drive application. There is not a lot of consistency as from one vehicle manufacturer to another as to how O2 sensors are labeled, so always refer to the OEM service literature to find out which sensor is Bank 1 Sensor 1 and which one is Bank 2 Sensor 1. This information can be difficult to find. Some OEMs clearly identify which O2 sensor is which but others do not. If in doubt, call a dealer and ask somebody in the service department.

     

    2.What's the difference between a "heated" and "unheated" oxygen sensor?
    Heated oxygen sensors have an internal heater circuit that brings the sensor up to operating temperature more quickly than an unheated sensor. An oxygen sensor must be hot (about 600 to 650 degrees F) before it will generate a voltage signal. The hot exhaust from the engine will provide enough heat to bring an O2 sensor up to operating temperature, but it make take several minutes depending on ambient temperature, engine load and speed. During this time, the fuel feedback control system remains in "open loop" and does not use the O2 sensor signal to adjust the fuel mixture. This typically results in a rich fuel mixture, wasted fuel and higher emissions.
    By adding an internal heater circuit to the oxygen sensor, voltage can be routed through the heater as soon as the engine starts to warm up the sensor. The heater element is a resistor that glows red hot when current passes through it. The heater will bring the sensor up to operating temperature within 20 to 60 seconds depending on the sensor, and also keep the oxygen sensor hot even when the engine is idling for a long period of time.
    Heated O2 sensors typically have two-three or four wires (the extra wires are for the heater circuit). Note: Replacement O2 sensors must have the same number of wires as the original, and have the same internal resistance.
    The OBD II system also monitors the heater circuit and will set a trouble code if the heater circuit inside the O2 sensor is defective. The heater is part of the sensor and cannot be replaced separately, so if the heater circuit is open or shorted and the problem is not in the external wiring or sensor connector, the O2 sensor must be replaced.

     

    Sweet Tips:
    1. If you are not sure the compatibility with your car, please timely contact us! We'll check and confirm the accurate and direct fitment info for you!
    2. If the items can not work with your car after installation, please timely contact us! we would provide our professional knowledge or exchange a new item.
    3. If you are not satisfied with our product or the order. please don't make a hesitate feedback straightly, please timely contact us via eBay message! We surely provide a solution for you within 24hours!
    We sincerely hope your support and understanding! 

     

     

     



    We accept paypal only

    We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    1. Items will be shipped within 24 hours after getting your verified payment.

    US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim

    1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.

    2.Any returning or exchanging item must be in new condition and cannot be tempered.

    3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.

    4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.

    We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)

    Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.


    All rights reserved.





    Brand: Autopartsclub2018
    Isin: IEHAHQSWUCOE

    $35.07

    • Free shipping in US

    • Arrives:

    • Free 30-Day returns

    In Stock

    Sold by , Fulfilled By IBSPOT
    Ships from USA

    IBspot Buyer Protection

    Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms

    supported payment methods:Visa, Mastercard, Discover, Amex, Apple Pay, Google Pay

    GUARANTEED SAFE CHECKOUT

    More seller options

    Starting from

    Compare all sellers

    • MONEY BACK GUARANTEE

      30 days money back guarantee, no additional fee charged.

    • EXCELLENT SUPPORT

      We provide 24/7 online customer support via email.

    • Fast Shipping

      One week domestic shipping. Global delivery to the US in 2 weeks.

    scroll to top arrow
    Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

    Autopartsclub2018 Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 0...

    $35.07

  • Features & Specifications:
  •  
    • Planar technology helps reduce emissions
    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 
     
  •  
  • Compatibility:
  •  
  • 2002 Infiniti G20 2.0L 2002-2004 Infiniti I35 3.5L 2001 Nissan Altima 2.4L 2002-2004 Nissan Altima 3.5L 2002-2004 Nissan Frontier 2.4L 2002-2003 Nissan Maxima 3.5L 2001 Nissan Sentra 1.8L 2002-2004 Nissan Xterra 2.4L
  •  
  •  
    		•
    Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

    Features & Specifications:

     

    • Planar technology helps reduce emissions

    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 

     

     

    Compatibility:

     

    2002 Infiniti G20 2.0L
    2002-2004 Infiniti I35 3.5L
    2001 Nissan Altima 2.4L
    2002-2004 Nissan Altima 3.5L
    2002-2004 Nissan Frontier 2.4L
    2002-2003 Nissan Maxima 3.5L
    2001 Nissan Sentra 1.8L
    2002-2004 Nissan Xterra 2.4L

     

     

    location:Upstream: location is between the catalytic converter and the engine

                  Downstream: location is between the catalytic converter and the tailpipe

    Oxygen Sensor Q & A

    1.How are the oxygen sensors identified on a scan tool?
    When displayed on a scan tool, the right and left upstream oxygen sensors are typically labeled Bank 1, Sensor 1 and Bank 2, Sensor 1. The Bank 1 sensor will always be on the same side of a V6 or V8 engine as cylinder number one.
    On a scan tool, the downstream sensor on a four or straight six cylinder engine with single exhaust is typically labeled Bank 1, Sensor 2. On a V6, V8 or V10 engine, the downstream O2 sensor might be labeled Bank 1 or Bank 2, Sensor 2. If a V6, V8 or V10 engine has dual exhausts with dual converters, the downstream O2 sensors would be labeled Bank 1, Sensor 2 and Bank 2, Sensor 2. Or, the downstream oxygen sensor might be labeled Bank 1 Sensor 3 if the engine has two upstream oxygen sensors in the exhaust manifold (some do to more accurately monitor emissions).
    It's important to know how the O2 sensors are identified because a diagnostic trouble code that indicates a faulty O2 sensor requires a specific sensor to be replaced. Bank 1 Sensor 1 might be the back O2 sensor on a transverse V6, or it might be the one on the front exhaust manifold. What's more, the O2 sensors on a transverse engine might be labeled differently than those on a rear-wheel drive application. There is not a lot of consistency as from one vehicle manufacturer to another as to how O2 sensors are labeled, so always refer to the OEM service literature to find out which sensor is Bank 1 Sensor 1 and which one is Bank 2 Sensor 1. This information can be difficult to find. Some OEMs clearly identify which O2 sensor is which but others do not. If in doubt, call a dealer and ask somebody in the service department.

     

    2.What's the difference between a "heated" and "unheated" oxygen sensor?
    Heated oxygen sensors have an internal heater circuit that brings the sensor up to operating temperature more quickly than an unheated sensor. An oxygen sensor must be hot (about 600 to 650 degrees F) before it will generate a voltage signal. The hot exhaust from the engine will provide enough heat to bring an O2 sensor up to operating temperature, but it make take several minutes depending on ambient temperature, engine load and speed. During this time, the fuel feedback control system remains in "open loop" and does not use the O2 sensor signal to adjust the fuel mixture. This typically results in a rich fuel mixture, wasted fuel and higher emissions.
    By adding an internal heater circuit to the oxygen sensor, voltage can be routed through the heater as soon as the engine starts to warm up the sensor. The heater element is a resistor that glows red hot when current passes through it. The heater will bring the sensor up to operating temperature within 20 to 60 seconds depending on the sensor, and also keep the oxygen sensor hot even when the engine is idling for a long period of time.
    Heated O2 sensors typically have two-three or four wires (the extra wires are for the heater circuit). Note: Replacement O2 sensors must have the same number of wires as the original, and have the same internal resistance.
    The OBD II system also monitors the heater circuit and will set a trouble code if the heater circuit inside the O2 sensor is defective. The heater is part of the sensor and cannot be replaced separately, so if the heater circuit is open or shorted and the problem is not in the external wiring or sensor connector, the O2 sensor must be replaced.

     

    Sweet Tips:
    1. If you are not sure the compatibility with your car, please timely contact us! We'll check and confirm the accurate and direct fitment info for you!
    2. If the items can not work with your car after installation, please timely contact us! we would provide our professional knowledge or exchange a new item.
    3. If you are not satisfied with our product or the order. please don't make a hesitate feedback straightly, please timely contact us via eBay message! We surely provide a solution for you within 24hours!
    We sincerely hope your support and understanding! 

     

     

     


    Item Specifics
    Manufacturer Part Number AP050760A1C18
    Brand Autopartsclub2018
    Manufacturer Warranty 1 Year
    Type Sensor
    Number of Pieces 1
    Interchange Part Number 234-3113C
    Other Part Number 13968-C
    Superseded Part Number 15340CW
    Custom Bundle No
    Fitment Type Direct Replacement
    Modified Item No
    Position Upstream
    Connector Gender Male
    Wire Harness Length(mm) 450
    Wire Quantity 3
    Pin Quantity 3
    Sensor Type Heated
    Thread Diameter 18mm
    Universal Or Specific Fit Specific
    Attachment Method Screw-On
    Terminal Type Blade
    Features Direct Fit
    Type Sensor
    Features Direct Fit

    Payment

    We accept paypal only

    We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    Shipping

    1. Items will be shipped within 24 hours after getting your verified payment.

    US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim

    Returns

    1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.

    2.Any returning or exchanging item must be in new condition and cannot be tempered.

    3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.

    4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.

    Contact Us

    We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)

    Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.

    Picture

    content_src_url

    content_src_url

    content_src_url
    Brand New Replacement Upstream Oxygen Sensor 3-Wire Front 02 O2 Fits 234-3113

    Features & Specifications:

     

    • Planar technology helps reduce emissions

    • PTFE filter blocks efficiency-robbing contaminants
    • Refined zirconia element improves sensor response
    • Superior design maximizes engine performance and fuel efficiency while reducing fuel consumption and harmful emissions
    • Ensures smog test compliance 

     

     

    Compatibility:

     

    2002 Infiniti G20 2.0L
    2002-2004 Infiniti I35 3.5L
    2001 Nissan Altima 2.4L
    2002-2004 Nissan Altima 3.5L
    2002-2004 Nissan Frontier 2.4L
    2002-2003 Nissan Maxima 3.5L
    2001 Nissan Sentra 1.8L
    2002-2004 Nissan Xterra 2.4L

     

     

    location:Upstream: location is between the catalytic converter and the engine

                  Downstream: location is between the catalytic converter and the tailpipe

    Oxygen Sensor Q & A

    1.How are the oxygen sensors identified on a scan tool?
    When displayed on a scan tool, the right and left upstream oxygen sensors are typically labeled Bank 1, Sensor 1 and Bank 2, Sensor 1. The Bank 1 sensor will always be on the same side of a V6 or V8 engine as cylinder number one.
    On a scan tool, the downstream sensor on a four or straight six cylinder engine with single exhaust is typically labeled Bank 1, Sensor 2. On a V6, V8 or V10 engine, the downstream O2 sensor might be labeled Bank 1 or Bank 2, Sensor 2. If a V6, V8 or V10 engine has dual exhausts with dual converters, the downstream O2 sensors would be labeled Bank 1, Sensor 2 and Bank 2, Sensor 2. Or, the downstream oxygen sensor might be labeled Bank 1 Sensor 3 if the engine has two upstream oxygen sensors in the exhaust manifold (some do to more accurately monitor emissions).
    It's important to know how the O2 sensors are identified because a diagnostic trouble code that indicates a faulty O2 sensor requires a specific sensor to be replaced. Bank 1 Sensor 1 might be the back O2 sensor on a transverse V6, or it might be the one on the front exhaust manifold. What's more, the O2 sensors on a transverse engine might be labeled differently than those on a rear-wheel drive application. There is not a lot of consistency as from one vehicle manufacturer to another as to how O2 sensors are labeled, so always refer to the OEM service literature to find out which sensor is Bank 1 Sensor 1 and which one is Bank 2 Sensor 1. This information can be difficult to find. Some OEMs clearly identify which O2 sensor is which but others do not. If in doubt, call a dealer and ask somebody in the service department.

     

    2.What's the difference between a "heated" and "unheated" oxygen sensor?
    Heated oxygen sensors have an internal heater circuit that brings the sensor up to operating temperature more quickly than an unheated sensor. An oxygen sensor must be hot (about 600 to 650 degrees F) before it will generate a voltage signal. The hot exhaust from the engine will provide enough heat to bring an O2 sensor up to operating temperature, but it make take several minutes depending on ambient temperature, engine load and speed. During this time, the fuel feedback control system remains in "open loop" and does not use the O2 sensor signal to adjust the fuel mixture. This typically results in a rich fuel mixture, wasted fuel and higher emissions.
    By adding an internal heater circuit to the oxygen sensor, voltage can be routed through the heater as soon as the engine starts to warm up the sensor. The heater element is a resistor that glows red hot when current passes through it. The heater will bring the sensor up to operating temperature within 20 to 60 seconds depending on the sensor, and also keep the oxygen sensor hot even when the engine is idling for a long period of time.
    Heated O2 sensors typically have two-three or four wires (the extra wires are for the heater circuit). Note: Replacement O2 sensors must have the same number of wires as the original, and have the same internal resistance.
    The OBD II system also monitors the heater circuit and will set a trouble code if the heater circuit inside the O2 sensor is defective. The heater is part of the sensor and cannot be replaced separately, so if the heater circuit is open or shorted and the problem is not in the external wiring or sensor connector, the O2 sensor must be replaced.

     

    Sweet Tips:
    1. If you are not sure the compatibility with your car, please timely contact us! We'll check and confirm the accurate and direct fitment info for you!
    2. If the items can not work with your car after installation, please timely contact us! we would provide our professional knowledge or exchange a new item.
    3. If you are not satisfied with our product or the order. please don't make a hesitate feedback straightly, please timely contact us via eBay message! We surely provide a solution for you within 24hours!
    We sincerely hope your support and understanding! 

     

     

     



    We accept paypal only

    We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!

    1. Items will be shipped within 24 hours after getting your verified payment.

    US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim

    1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.

    2.Any returning or exchanging item must be in new condition and cannot be tempered.

    3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.

    4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.

    We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)

    Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.


    All rights reserved.





    • Manufacturer Part Number: AP050760A1C18
    • Brand: Autopartsclub2018
    • Manufacturer Warranty: 1 Year
    • Type: Sensor
    • Number of Pieces: 1
    • UPC: Does not apply
    • Interchange Part Number: 234-3113C
    • Other Part Number: 13968-C
    • Superseded Part Number: 15340CW
    • Custom Bundle: No
    • Fitment Type: Direct Replacement
    • Modified Item: No
    • Position: Upstream
    • Connector Gender: Male
    • Wire Harness Length(mm): 450
    • Wire Quantity: 3
    • Pin Quantity: 3
    • Sensor Type: Heated
    • Thread Diameter: 18mm
    • Universal Or Specific Fit: Specific
    • Attachment Method: Screw-On
    • Terminal Type: Blade
    • Features: Direct Fit

     

    Processing Time

    • We process and ship orders Monday through Friday, excluding holidays.
    • Most orders are processed within 1–3 business days, depending on product availability.
    • Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.

    Shipping Coverage

    We currently ship to addresses within the United States only.

    Products may ship from:

    • Our U.S. warehouses, or
    • Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).

    Each product page clearly displays the “Ships From” location before checkout.

    Shipping Methods & Estimated Delivery

     

    Shipping Method Estimated Delivery Cost
    Free Shipping (US) 5–10 business days Free, available on eligible items
    Standard Shipping (US to US by Item) 5–10 business days $6.50 for the first item, $3.00 each additional
    Standard Shipping (From US Warehouse by Weight) 3–7 business days Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb.
    Extended Delivery (Ships from Overseas Warehouse) 10–15 business days $14.50 for the first item, $4.00 each additional

    Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.

    Free Shipping

    We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout. 

    Carriers

    We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.

    Import Duties & Taxes

    All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.

    Tracking & Notifications

    Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.

    You can track your shipment anytime using the Track Your Order page on our website.

    Order Changes & Cancellations

    If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.

    Contact: support@ibspot.com

    Item Not Received

    If your tracking number shows “Delivered” but you haven’t received your package:

    1. Check with your local USPS or UPS office.
    2. Confirm that the shipping address provided was correct.
    3. If the issue remains unresolved, contact support@ibspot.com for assistance.

    Damaged or Lost Parcels

    If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.

    Customer Support

    For any questions about shipping, tracking, or delivery, our customer support team is here to help.

    Email: support@ibspot.com

    We’re always happy to help.

    Please read our policy carefully before making a purchase.
    We aim to ensure every customer has a smooth and transparent experience with ibspot.com.

    Order Cancellation Policy

    Customers may request to cancel an order before it has been shipped.
    Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.

    How to Request a Cancellation

    You can contact us through:

    Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.

    Return Policy

    We accept returns for most items within 30 days of delivery for a full refund.

    To be eligible for a return:

    • The item must be unused, in the same condition as received, and in its original packaging.

    • A tracking number must be provided to confirm the return shipment.

    Non-Returnable Items

    Certain products cannot be returned, including:

    • Perishable goods (for example, food, flowers, newspapers, magazines)

    • Intimate or sanitary goods

    • Hazardous materials or flammable liquids/gases

    • Gift cards

    • Downloadable software

    • Some health and personal care items

    Partial Refunds (If Applicable)

    Partial refunds may be granted in specific situations, such as:

    • Books with obvious signs of use

    • Opened CDs, DVDs, software, or vinyl records

    • Items not in their original condition, damaged, or missing parts not due to our error

    • Items returned more than 30 days after delivery

    How to Return an Item

    To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
    Our team will provide you with return instructions and a prepaid return label.

    Shipping Cost for Returns

    Please contact us before returning any item.
    We will provide a free return shipping label.

    If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.

    For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
    We cannot guarantee that we will receive your returned item if shipped independently.

    Refund Processing

    Once your return is received and inspected:

    • In-store returns are refunded to the original form of payment or issued as a gift card.

    • Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.

    Please allow:

    • 5–7 business days for the return to reach our Returns Center.

    • An additional 3–10 business days for your bank to post the refund to your account.

    Damages, Issues & Claims

    Please inspect your order immediately upon receipt.
    If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
    We’ll evaluate the issue promptly and make it right.

    Product Claims

    Before purchasing, please review product details carefully.
    If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.

    Exchanges

    We do not process direct exchanges.
    The fastest way to get what you need is to return the original item and place a new order once your return is accepted.

    Return Address

    IBSPOT Return Center
    15 Sawmill Ln
    Dover Plains, NY 12522
    United States

    Customer Support

    Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.

    Email: support@ibspot.com
    Contact Form: Contact Us page

    Oops!

    Sorry, it looks like some products are not available in selected quantity.

    OK

    delivery truck
    Fast Delivery

    Global delivery to the US in just days—fast, reliable, and hassle-free service every time!

    safe payment
    Safe Payment

    Pay with the world’s most popular and secure payment methods.

    headphone
    24/7 Help Center

    Round-the-clock assistance for a smooth shopping experience.

    mail return
    100% Satisfaction Guarantee

    30 days return policy if you’re not satisfied with products & services

    Subscribe To Our Newsletter

    Disclaimer: Statements made, or products sold through this website, have not been evaluated by the United States Food and Drug Administration. Products are not intended to diagnose, treat, cure or prevent any disease.