SCITOO Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
SCITOO Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
SCITOO Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
|
|
|
|
|
|
|
|
|
|
|
|
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications
Scion FR-S 2.0L 2013-2016
Subaru BRZ 2.0L 2013-2020
Toyota 86 2.0L 2017-2020
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
?
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications
Scion FR-S 2.0L 2013-2016
Subaru BRZ 2.0L 2013-2020
Toyota 86 2.0L 2017-2020
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
?
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
| Item Specifics | |
|---|---|
| Brand | SCITOO |
| Manufacturer Part Number | CB118123S01 |
| Fitment Type | Direct Replacement |
| Bore Diameter | 64MM |
| Connector Quantity | 1 |
| Fuel System Type | FI |
| Gaskets Included | No |
| Throttle Body Actuation Type | Electrical |
| Items Included | One Complete Throttle Body w/Sensor |
| Packaging Type | Box |
| Modified Item | No |
| Custom Bundle | No |
| Placement on Vehicle | Front |
| Non-Domestic Product | Yes |
| Mounting Hardware Included | No |
| Manufacturer Warranty | 1 Year |
| Interchange Part Number | 16112AA400, SU00300313 |
| OE/OEM Part Number | 67-7005, S20202, 337-02181 |
| Superseded Part Number | S20199, 672108, TB1286, 977079 |
| Weight | 3 LB |
| Type | Throttle Body |
| Features | Electronic |
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
Payment
1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc..
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as auction ended or order might be delayed.
Returns
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services
Q: How do I pay for my purchase?
A: MY store accepts PayPal, VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
Feedback
1. We will leave a feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category Warranty |
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications Scion FR-S 2.0L 2013-2016
Electronic Throttle Body the usual parts
The mechanic will replace the throttle body on your car if:
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers. Throttle Body Replacement 1. Refer to the service manual for identification and location of the throttle body. 2. Remove the air intake duct from the throttle body once it is located. 3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement. 4. Pull out the cables from the throttle body. 5. Remove the hoses such as air or vacuum hoses from the throttle body. ? 6. Disconnect the throttle position sensor. 7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything. 9. Properly clean the assembly and port to remove any carbon build up. 10. Compare the old throttle body with the new one.
11. Install the throttle body in the port. 12. Fasten the bolts and screws to hold it in place. 13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body. 15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn? Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need? Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required? As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn? In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire). If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn? Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. Payment
1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns
1.All of our brand new items come with a 60-Days money-back guarantee. Customer Services
Q: How do I pay for my purchase? Feedback
1. We will leave a feedback once we get your payment. Copyright of SCITOO-AutoParts . All rights reserved. |
| Brand: | SCITOO |
|---|---|
| Isin: | IJRRCVH9HVVZ |
This product is not available in the selected country
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
|
|
|
|
|
|
|
|
|
|
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications
Scion FR-S 2.0L 2013-2016
Subaru BRZ 2.0L 2013-2020
Toyota 86 2.0L 2017-2020
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
?
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications
Scion FR-S 2.0L 2013-2016
Subaru BRZ 2.0L 2013-2020
Toyota 86 2.0L 2017-2020
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
?
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
| Item Specifics | |
|---|---|
| Brand | SCITOO |
| Manufacturer Part Number | CB118123S01 |
| Fitment Type | Direct Replacement |
| Bore Diameter | 64MM |
| Connector Quantity | 1 |
| Fuel System Type | FI |
| Gaskets Included | No |
| Throttle Body Actuation Type | Electrical |
| Items Included | One Complete Throttle Body w/Sensor |
| Packaging Type | Box |
| Modified Item | No |
| Custom Bundle | No |
| Placement on Vehicle | Front |
| Non-Domestic Product | Yes |
| Mounting Hardware Included | No |
| Manufacturer Warranty | 1 Year |
| Interchange Part Number | 16112AA400, SU00300313 |
| OE/OEM Part Number | 67-7005, S20202, 337-02181 |
| Superseded Part Number | S20199, 672108, TB1286, 977079 |
| Weight | 3 LB |
| Type | Throttle Body |
| Features | Electronic |
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
Payment
1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc..
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as auction ended or order might be delayed.
Returns
1.All of our brand new items come with a 60-Days money-back guarantee.
2.We define the item as defective only if it doesn't function as described, It is the buyer's responsibility to understand the item description before bidding.
3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement.
4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost.
5.Shipping& handling cost are not refundable.
6.Man-made damage by abuse or wrong operation is not covered by this warranty.
7.No product liability insurance is assumed.
8.Refunds will be credited within 5 to 7 business days of receiving the return. When we've received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ]
Customer Services
Q: How do I pay for my purchase?
A: MY store accepts PayPal, VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
Feedback
1. We will leave a feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category New List Item
Hot Item
Warranty
|
Throttle Body For Toyota 86 2017-2020 Scion FR-S 2013-2016 BRZ 2013-2020 2.0L
Fits Applications Scion FR-S 2.0L 2013-2016
Electronic Throttle Body the usual parts
The mechanic will replace the throttle body on your car if:
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers. Throttle Body Replacement 1. Refer to the service manual for identification and location of the throttle body. 2. Remove the air intake duct from the throttle body once it is located. 3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement. 4. Pull out the cables from the throttle body. 5. Remove the hoses such as air or vacuum hoses from the throttle body. ? 6. Disconnect the throttle position sensor. 7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything. 9. Properly clean the assembly and port to remove any carbon build up. 10. Compare the old throttle body with the new one.
11. Install the throttle body in the port. 12. Fasten the bolts and screws to hold it in place. 13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body. 15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn? Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need? Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required? As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn? In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire). If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn? Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
Shipping
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. Payment
1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns
1.All of our brand new items come with a 60-Days money-back guarantee. Customer Services
Q: How do I pay for my purchase? Feedback
1. We will leave a feedback once we get your payment. Copyright of SCITOO-AutoParts . All rights reserved. |
- Brand: SCITOO
- Manufacturer Part Number: CB118123S01
- Fitment Type: Direct Replacement
- Bore Diameter: 64MM
- Connector Quantity: 1
- Fuel System Type: FI
- Gaskets Included: No
- Throttle Body Actuation Type: Electrical
- Items Included: One Complete Throttle Body w/Sensor
- Packaging Type: Box
- UPC: Does not apply
- Modified Item: No
- Custom Bundle: No
- Placement on Vehicle: Front
- Non-Domestic Product: Yes
- Mounting Hardware Included: No
- Manufacturer Warranty: 1 Year
- Interchange Part Number: 16112AA400, SU00300313
- OE/OEM Part Number: 67-7005, S20202, 337-02181
- Superseded Part Number: S20199, 672108, TB1286, 977079
- Type: Throttle Body
- Features: Electronic
Shipping Summary:
- Packages are shipped from Monday to Friday.
- The usual time for processing an order is 1 to 3 business days, but may vary depending on the availability of products ordered. This period excludes delivery times, which depend on your geographic location.
- We provide tracking for every order. Tracking will be available once your product is shipped. Each individual product may be shipped from different fulfillment centers across the globe as our product research team spends the time to source quality yet affordable products.
Estimated delivery times:
- Standard Shipping: 3-7 business days
- Expedited Shipping: 2-5 business days
- International Shipping: 10 - 15 business days
Please note that these are estimates, not guarantees. Delivery time depends on a number of variables, and there may be delays such as bad weather affecting air transport, or a package being held for inspection by Customs. ibspot is not liable for any delays in international transportation or customs clearance.
Shipments can be delivered directly to most addresses, except post office boxes. However, in certain remote areas, there may be an additional delivery charge or you may need to pick up your package from the closest service location of ibspot's shipping partner.
Shipping Status:
As soon as your order ships, you'll receive a shipping confirmation email that includes your tracking number.
If you don't receive a shipping confirmation email right away, don't worry! We know the delivery date or date range provided at checkout and we'll be sure to deliver the items within that timeframe.
Order changes:
Please contact our customer support if the order needs to be canceled or modified.
Item not received:
If you've successfully placed an order and haven't received it yet while the tracking status shows it's delivered. you'd wish to contact the carrier to hunt the packages. Once a package is marked “Delivered” by the carrier, we are no longer responsible for lost or stolen items. Please ensure you provide a secure delivery address.
Damaged Parcel
If your package has been delivered in a PO Box, please note that we are not responsible for any damage that may result (consequences of extreme temperatures, theft, etc.).
If you have any questions regarding shipping or want to know about the status of an order, please contact us or email to support@ibspot.com.
Please Read Our Return & Refund Policy Carefully:
Return:
You may return most items within 30 days of delivery for a full refund.
To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.
Several types of goods are exempt from being returned. Perishable goods such as food, flowers, newspapers or magazines cannot be returned. We also do not accept products that are intimate or sanitary goods, hazardous materials, or flammable liquids or gases.
Additional non-returnable items:
- Gift cards
- Downloadable software products
- Some health and personal care items
To complete your return, we require a tracking number, which shows the items which you already returned to us.
There are certain situations where only partial refunds are granted (if applicable)
- Book with obvious signs of use
- CD, DVD, VHS tape, software, video game, cassette tape, or vinyl record that has been opened
- Any item not in its original condition, is damaged or missing parts for reasons not due to our error
- Any item that is returned more than 30 days after delivery
Items returned to us as a result of our error will receive a full refund,some returns may be subject to a restocking fee of 7% of the total item price, please contact a customer care team member to see if your return is subject. Returns that arrived on time and were as described are subject to a restocking fee.
Items returned to us that were not the result of our error, including items returned to us due to an invalid or incomplete address, will be refunded the original item price less our standard restocking fees.
You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).
If you need to return an item, please Contact Us with your order number and details about the product you would like to return. We will respond quickly with instructions for how to return items from your order.
Shipping Cost
We'll pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.). In other cases, you will be responsible for paying for your own shipping costs for returning your item. Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
Depending on where you live, the time it may take for your exchanged product to reach you, may vary.
If you are shipping an item over $75, you should consider using a trackable shipping service or purchasing shipping insurance. We don’t guarantee that we will receive your returned item.
Refund:
- Purchases may be returned within 30 days of the shipping date for a refund.
- Refund will be issued to your original form of payment.
- Refunds for orders purchased with IBSPOT Gift Cards and/or IBSPOT Notes will be issued as a IBSPOT Gift Card and mailed to the original billing address. Gift cards cannot be redeemed for cash unless required by law.
Refund Processing
• Returns to a IBSPOT store will be refunded to the original form of payment or gift card. • Mail-in returns with our prepaid return label will be refunded back to the original form of payment within 3-5 business days after we receive your return. Please allow 5-7 business days for your return to arrive at our Returns Center.
• Note: It may take a few days until your bank posts the refund to your account.
Claims:
Claims related to the product. Be sure to check the details of your purchase carefully before you make the payment, and check the contents of the package(s) promptly upon receipt. If you have a problem with the product, visit our Support Center to find out about return shipping arrangements.
WHICH CIRCUMSTANCES WE OFFER RETURND & REFUND:
WRONG PRODUCT:
If you discover your order is flawed please contact us Mail: support@ibspot.com. With photos of the wrong product we will providing a return shipping label. Once it is tracking we will ship a replacement a product immediately.
Damages and issues
Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right.
Exceptions / non-returnable items
Certain types of items cannot be returned, like perishable goods (such as food, flowers, or plants), custom products (such as special orders or personalized items), and personal care goods (such as beauty products). We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item. Unfortunately, we cannot accept returns on sale items or gift cards.
Exchanges
The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item.
Oops!
Sorry, it looks like some products are not available in selected quantity.
