Turboshop 70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
Turboshop 70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
Turboshop 70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
|
|
|
||||||
|
|
|
|
|
|||
|
|
|
|
|
|||
70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
What is a throttle body ?
The throttle body is the part of the engine that mixes air with the fuel to allow combustion to take place. When a throttle body gets clogged with carbon, the vehicle may suffer from issues ranging from a lack of fuel mileage, loss in efficiency or may even become totally inoperable.
When you need to replace the throttle body:
1. Check engine light and/or reduced power warning light is on. If the check engine light or reduced power warning light comes on, a mechanic will determine if any of the stored trouble codes implicate a throttle body malfunction.
2. Wrong idle speed.
3. Poor transmission shifting.
WARNING !
1. Do not disconnect any electrical connectors to the electronic throttle body assembly with the ignition switch in the “ON” position. Make sure the ignition key is in the off position first.
2. Additional components may need to be removed before proceeding with the electronic throttle body removal.
3. Some electronic throttle body assemblies have coolant hose attachments that must be removed during replacement. To prevent coolant loss, plug hoses upon removal.
4. After the replacement of the electronic throttle body, the idle speed may be Different or Vary. A Relearn procedure may be required on the vehicle. Refer to the appropriate technical service repair manual and follow “Relearn” instructions.
Replace the throttle body:
You will need: Gasket Scraper, Pier Assortment, Screwddriver Assortment, Socket Set, Wrench Set
Steps:
1. Remove the engine cover , if necessary.
2. Important:Remove the negative battery cable.
3. Remove the air intake hose.
(There may also be some water cables attached to the throttle body. If this is the case remove the hose clamps using pliers before you remove the hoses. )
4. Remove the electrical connections.
5. Remove the water hose.
(If your throttle body does not have connected the water hose, you can skip this step. )
6. Remove the mounting hardware and old electronic throttle body
7. Remove the old gasket
8. Clean the mounting surface
9. Install the new gasket
10. Install the new electronic throttle body
11. Torque the bolts to spec
12. Reattach the water hose
13. Reattach the electrical connections
14. Reattach the air intake hose
15. Important: Reattach the battery cable
16. If applicable, the electronic throttle installation and idle re-learn procedures are performed using an appropriate scan tool.
17. Finally, the engine is started, brought to normal operating temperature, and idle speed is checked. The car is road tested to ensure normal operation and no illumination of warning or service lights.
Don't forget to relearn the new replaced ETB!
Here is the throttle body relearn procedure:
1. Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal.
2. After 3 minutes, turn the engine off and leave it off for 60- seconds.
3. Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light. Scan for codes and if you get throttle body related codes, clear them.
4. If the idle speed is still off, drive the vehicle at speeds above 44-mph and operate several acceleration and deceleration cycles. Then repeat step #3 one last time.
Some tips for locating the throttle body under the hood in the Engine Compartment:
• Throttle body is situated between the air cleaner and intake manifold
• Throttle body is made from aluminum
• In some older models, the throttle body is connected to the gas pedal by metal wire so you can identify it by pressing the gas pedal while the engine is shut off and see the moving part.
• Once you find the throttle body, you have to be careful when dealing with it. This is because there are tubes and hoses and, in some cases, electrical connections attached to it.
Is it safe to drive with a throttle body problem?
Yes. But, the vehicle may be limited in power or put into what is referred to as limp mode, in order to get the vehicle to a repair facility. If the check engine light is on, or the electronic throttle control warning light is on, but there is no noticeable difference in engine performance, the car can be safely driven. However, it is best to have it diagnosed and repaired at your earliest convenience to avoid unexpected breakdown or possible damage to the catalytic converter.
Why would a throttle body go bad?
One of the main causes of a malfunctioning throttle body is internal contamination. ... This causes 'false air' to be sucked in, so that the total amount of air sucked in does not correspond to the position of the throttle valve. An incorrectly adjusted throttle position sensor can also cause an engine to run badly.
Does throttle body need to be replaced?
The throttle body plays a large role in controlling the fuel and air mixture in your engine. The proper mixture needs to be achieved in order for your engine to run smoothly and properly. Once this part fails, it needs replacing rather than repairing.
What happens if you don't replace a throttle body?
When a throttle body is not functioning correctly, yourll usually notice a distinctly poor or very low idle. If the problem is really severe, you might even begin stalling when coming to a stop or when the throttle is quickly pressed.
Vehicle Compatibility Information
Acura Integra 1.7L 1992-1993
Acura Integra 1.8L 1990-2001
Honda Civic 1.5L 1992-1995
Honda Civic 1.6L 1992-2000
Honda Civic 1.7L 2001
Honda Civic del Sol 1.5L 1993-1995
Honda Civic del Sol 1.6L 1993-1997
Honda Prelude 2.2L 1992-2001
Honda Prelude 2.3L 1992-1996
Honda S2000 2.0L 2000-2003
Honda S2000 2.2L 2004-2009
| Item Specifics | |
|---|---|
| Brand | Turboshop |
| Manufacturer Part Number | ECP16149301S |
| Mounting Hardware Included | No |
| Manufacturer Warranty | 1 Year |
| Custom Bundle | No |
| Fitment Type | Direct Replacement |
| Material | Aluminum |
| Color | Metal |
| Weight | 2 LB |
| OE Spec or Performance/Custom | Performance/Custom |
| Items Included | 1 Fuel Injection Throttle Body |
| Package Quantity | 1 Throttle Body |
| Packaging Type | Box |
| Interchange Part Number | 309-05-1050 |
| OE/OEM Part Number | 309051050 |
| Superseded Part Number | 309-051050 |
| Type | Throttle Body |
| Placement on Vehicle | Front |
| Features | Electronic |
| Bore Diameter | 70mm |
Payment
Visa, and MasterCard are the accepted forms of payment.
Please use the eBay checkout system when paying for your order.
Immediate payment is required for all orders.
Shipping
International orders will ship through eBay's Global Shipping Program. Please keep in mind that we are not responsible for any import duties or fees.
Returns
All of our brand new items come with a 30-Days money-back guarantee.
Contact Us
Any question, please contact us by email on working days.
Best Sales Terms & Contact Payment Policy Shipping Policy Return Policy FAQ About Us |
70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
What is a throttle body ? The throttle body is the part of the engine that mixes air with the fuel to allow combustion to take place. When a throttle body gets clogged with carbon, the vehicle may suffer from issues ranging from a lack of fuel mileage, loss in efficiency or may even become totally inoperable.
When you need to replace the throttle body: 1. Check engine light and/or reduced power warning light is on. If the check engine light or reduced power warning light comes on, a mechanic will determine if any of the stored trouble codes implicate a throttle body malfunction. 2. Wrong idle speed. 3. Poor transmission shifting.
WARNING ! 1. Do not disconnect any electrical connectors to the electronic throttle body assembly with the ignition switch in the “ON” position. Make sure the ignition key is in the off position first. 2. Additional components may need to be removed before proceeding with the electronic throttle body removal. 3. Some electronic throttle body assemblies have coolant hose attachments that must be removed during replacement. To prevent coolant loss, plug hoses upon removal. 4. After the replacement of the electronic throttle body, the idle speed may be Different or Vary. A Relearn procedure may be required on the vehicle. Refer to the appropriate technical service repair manual and follow “Relearn” instructions.
Replace the throttle body: You will need: Gasket Scraper, Pier Assortment, Screwddriver Assortment, Socket Set, Wrench Set Steps: 1. Remove the engine cover , if necessary. 2. Important:Remove the negative battery cable.
3. Remove the air intake hose. (There may also be some water cables attached to the throttle body. If this is the case remove the hose clamps using pliers before you remove the hoses. ) 4. Remove the electrical connections.
5. Remove the water hose. (If your throttle body does not have connected the water hose, you can skip this step. )
6. Remove the mounting hardware and old electronic throttle body 7. Remove the old gasket 8. Clean the mounting surface
9. Install the new gasket 10. Install the new electronic throttle body 11. Torque the bolts to spec 12. Reattach the water hose 13. Reattach the electrical connections
14. Reattach the air intake hose 15. Important: Reattach the battery cable
16. If applicable, the electronic throttle installation and idle re-learn procedures are performed using an appropriate scan tool. 17. Finally, the engine is started, brought to normal operating temperature, and idle speed is checked. The car is road tested to ensure normal operation and no illumination of warning or service lights.
Don't forget to relearn the new replaced ETB!
Here is the throttle body relearn procedure: 1. Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2. After 3 minutes, turn the engine off and leave it off for 60- seconds. 3. Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light. Scan for codes and if you get throttle body related codes, clear them. 4. If the idle speed is still off, drive the vehicle at speeds above 44-mph and operate several acceleration and deceleration cycles. Then repeat step #3 one last time.
Some tips for locating the throttle body under the hood in the Engine Compartment: • Throttle body is situated between the air cleaner and intake manifold • Throttle body is made from aluminum • In some older models, the throttle body is connected to the gas pedal by metal wire so you can identify it by pressing the gas pedal while the engine is shut off and see the moving part. • Once you find the throttle body, you have to be careful when dealing with it. This is because there are tubes and hoses and, in some cases, electrical connections attached to it.
Is it safe to drive with a throttle body problem? Yes. But, the vehicle may be limited in power or put into what is referred to as limp mode, in order to get the vehicle to a repair facility. If the check engine light is on, or the electronic throttle control warning light is on, but there is no noticeable difference in engine performance, the car can be safely driven. However, it is best to have it diagnosed and repaired at your earliest convenience to avoid unexpected breakdown or possible damage to the catalytic converter.
Why would a throttle body go bad? One of the main causes of a malfunctioning throttle body is internal contamination. ... This causes 'false air' to be sucked in, so that the total amount of air sucked in does not correspond to the position of the throttle valve. An incorrectly adjusted throttle position sensor can also cause an engine to run badly.
Does throttle body need to be replaced? The throttle body plays a large role in controlling the fuel and air mixture in your engine. The proper mixture needs to be achieved in order for your engine to run smoothly and properly. Once this part fails, it needs replacing rather than repairing.
What happens if you don't replace a throttle body? When a throttle body is not functioning correctly, yourll usually notice a distinctly poor or very low idle. If the problem is really severe, you might even begin stalling when coming to a stop or when the throttle is quickly pressed.
Vehicle Compatibility Information Acura Integra 1.7L 1992-1993 Visa, and MasterCard are the accepted forms of payment.
Please use the eBay checkout system when paying for your order.
Immediate payment is required for all orders.
International orders will ship through eBay's Global Shipping Program. Please keep in mind that we are not responsible for any import duties or fees. All of our brand new items come with a 30-Days money-back guarantee. Any question, please contact us by email on working days. All rights reserved. |
||||||||||||||||||
| Brand: | Turboshop |
|---|---|
| Isin: | IUBMAQHWZAB7 |
Out of Stock
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.
|
|
||||||
|
|
|
|
|||
|
|
|
|
|||
70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
What is a throttle body ?
The throttle body is the part of the engine that mixes air with the fuel to allow combustion to take place. When a throttle body gets clogged with carbon, the vehicle may suffer from issues ranging from a lack of fuel mileage, loss in efficiency or may even become totally inoperable.
When you need to replace the throttle body:
1. Check engine light and/or reduced power warning light is on. If the check engine light or reduced power warning light comes on, a mechanic will determine if any of the stored trouble codes implicate a throttle body malfunction.
2. Wrong idle speed.
3. Poor transmission shifting.
WARNING !
1. Do not disconnect any electrical connectors to the electronic throttle body assembly with the ignition switch in the “ON” position. Make sure the ignition key is in the off position first.
2. Additional components may need to be removed before proceeding with the electronic throttle body removal.
3. Some electronic throttle body assemblies have coolant hose attachments that must be removed during replacement. To prevent coolant loss, plug hoses upon removal.
4. After the replacement of the electronic throttle body, the idle speed may be Different or Vary. A Relearn procedure may be required on the vehicle. Refer to the appropriate technical service repair manual and follow “Relearn” instructions.
Replace the throttle body:
You will need: Gasket Scraper, Pier Assortment, Screwddriver Assortment, Socket Set, Wrench Set
Steps:
1. Remove the engine cover , if necessary.
2. Important:Remove the negative battery cable.
3. Remove the air intake hose.
(There may also be some water cables attached to the throttle body. If this is the case remove the hose clamps using pliers before you remove the hoses. )
4. Remove the electrical connections.
5. Remove the water hose.
(If your throttle body does not have connected the water hose, you can skip this step. )
6. Remove the mounting hardware and old electronic throttle body
7. Remove the old gasket
8. Clean the mounting surface
9. Install the new gasket
10. Install the new electronic throttle body
11. Torque the bolts to spec
12. Reattach the water hose
13. Reattach the electrical connections
14. Reattach the air intake hose
15. Important: Reattach the battery cable
16. If applicable, the electronic throttle installation and idle re-learn procedures are performed using an appropriate scan tool.
17. Finally, the engine is started, brought to normal operating temperature, and idle speed is checked. The car is road tested to ensure normal operation and no illumination of warning or service lights.
Don't forget to relearn the new replaced ETB!
Here is the throttle body relearn procedure:
1. Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal.
2. After 3 minutes, turn the engine off and leave it off for 60- seconds.
3. Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light. Scan for codes and if you get throttle body related codes, clear them.
4. If the idle speed is still off, drive the vehicle at speeds above 44-mph and operate several acceleration and deceleration cycles. Then repeat step #3 one last time.
Some tips for locating the throttle body under the hood in the Engine Compartment:
• Throttle body is situated between the air cleaner and intake manifold
• Throttle body is made from aluminum
• In some older models, the throttle body is connected to the gas pedal by metal wire so you can identify it by pressing the gas pedal while the engine is shut off and see the moving part.
• Once you find the throttle body, you have to be careful when dealing with it. This is because there are tubes and hoses and, in some cases, electrical connections attached to it.
Is it safe to drive with a throttle body problem?
Yes. But, the vehicle may be limited in power or put into what is referred to as limp mode, in order to get the vehicle to a repair facility. If the check engine light is on, or the electronic throttle control warning light is on, but there is no noticeable difference in engine performance, the car can be safely driven. However, it is best to have it diagnosed and repaired at your earliest convenience to avoid unexpected breakdown or possible damage to the catalytic converter.
Why would a throttle body go bad?
One of the main causes of a malfunctioning throttle body is internal contamination. ... This causes 'false air' to be sucked in, so that the total amount of air sucked in does not correspond to the position of the throttle valve. An incorrectly adjusted throttle position sensor can also cause an engine to run badly.
Does throttle body need to be replaced?
The throttle body plays a large role in controlling the fuel and air mixture in your engine. The proper mixture needs to be achieved in order for your engine to run smoothly and properly. Once this part fails, it needs replacing rather than repairing.
What happens if you don't replace a throttle body?
When a throttle body is not functioning correctly, yourll usually notice a distinctly poor or very low idle. If the problem is really severe, you might even begin stalling when coming to a stop or when the throttle is quickly pressed.
Vehicle Compatibility Information
Acura Integra 1.7L 1992-1993
Acura Integra 1.8L 1990-2001
Honda Civic 1.5L 1992-1995
Honda Civic 1.6L 1992-2000
Honda Civic 1.7L 2001
Honda Civic del Sol 1.5L 1993-1995
Honda Civic del Sol 1.6L 1993-1997
Honda Prelude 2.2L 1992-2001
Honda Prelude 2.3L 1992-1996
Honda S2000 2.0L 2000-2003
Honda S2000 2.2L 2004-2009
| Item Specifics | |
|---|---|
| Brand | Turboshop |
| Manufacturer Part Number | ECP16149301S |
| Mounting Hardware Included | No |
| Manufacturer Warranty | 1 Year |
| Custom Bundle | No |
| Fitment Type | Direct Replacement |
| Material | Aluminum |
| Color | Metal |
| Weight | 2 LB |
| OE Spec or Performance/Custom | Performance/Custom |
| Items Included | 1 Fuel Injection Throttle Body |
| Package Quantity | 1 Throttle Body |
| Packaging Type | Box |
| Interchange Part Number | 309-05-1050 |
| OE/OEM Part Number | 309051050 |
| Superseded Part Number | 309-051050 |
| Type | Throttle Body |
| Placement on Vehicle | Front |
| Features | Electronic |
| Bore Diameter | 70mm |
Payment
Visa, and MasterCard are the accepted forms of payment.
Please use the eBay checkout system when paying for your order.
Immediate payment is required for all orders.
Shipping
International orders will ship through eBay's Global Shipping Program. Please keep in mind that we are not responsible for any import duties or fees.
Returns
All of our brand new items come with a 30-Days money-back guarantee.
Contact Us
Any question, please contact us by email on working days.
Best Sales Newly Listed
Terms & Contact Payment Policy Shipping Policy Return Policy FAQ About Us |
70MM Throttle Body w/Sensor For Honda S2000 Acura Integras B D F H
What is a throttle body ? The throttle body is the part of the engine that mixes air with the fuel to allow combustion to take place. When a throttle body gets clogged with carbon, the vehicle may suffer from issues ranging from a lack of fuel mileage, loss in efficiency or may even become totally inoperable.
When you need to replace the throttle body: 1. Check engine light and/or reduced power warning light is on. If the check engine light or reduced power warning light comes on, a mechanic will determine if any of the stored trouble codes implicate a throttle body malfunction. 2. Wrong idle speed. 3. Poor transmission shifting.
WARNING ! 1. Do not disconnect any electrical connectors to the electronic throttle body assembly with the ignition switch in the “ON” position. Make sure the ignition key is in the off position first. 2. Additional components may need to be removed before proceeding with the electronic throttle body removal. 3. Some electronic throttle body assemblies have coolant hose attachments that must be removed during replacement. To prevent coolant loss, plug hoses upon removal. 4. After the replacement of the electronic throttle body, the idle speed may be Different or Vary. A Relearn procedure may be required on the vehicle. Refer to the appropriate technical service repair manual and follow “Relearn” instructions.
Replace the throttle body: You will need: Gasket Scraper, Pier Assortment, Screwddriver Assortment, Socket Set, Wrench Set Steps: 1. Remove the engine cover , if necessary. 2. Important:Remove the negative battery cable.
3. Remove the air intake hose. (There may also be some water cables attached to the throttle body. If this is the case remove the hose clamps using pliers before you remove the hoses. ) 4. Remove the electrical connections.
5. Remove the water hose. (If your throttle body does not have connected the water hose, you can skip this step. )
6. Remove the mounting hardware and old electronic throttle body 7. Remove the old gasket 8. Clean the mounting surface
9. Install the new gasket 10. Install the new electronic throttle body 11. Torque the bolts to spec 12. Reattach the water hose 13. Reattach the electrical connections
14. Reattach the air intake hose 15. Important: Reattach the battery cable
16. If applicable, the electronic throttle installation and idle re-learn procedures are performed using an appropriate scan tool. 17. Finally, the engine is started, brought to normal operating temperature, and idle speed is checked. The car is road tested to ensure normal operation and no illumination of warning or service lights.
Don't forget to relearn the new replaced ETB!
Here is the throttle body relearn procedure: 1. Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2. After 3 minutes, turn the engine off and leave it off for 60- seconds. 3. Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light. Scan for codes and if you get throttle body related codes, clear them. 4. If the idle speed is still off, drive the vehicle at speeds above 44-mph and operate several acceleration and deceleration cycles. Then repeat step #3 one last time.
Some tips for locating the throttle body under the hood in the Engine Compartment: • Throttle body is situated between the air cleaner and intake manifold • Throttle body is made from aluminum • In some older models, the throttle body is connected to the gas pedal by metal wire so you can identify it by pressing the gas pedal while the engine is shut off and see the moving part. • Once you find the throttle body, you have to be careful when dealing with it. This is because there are tubes and hoses and, in some cases, electrical connections attached to it.
Is it safe to drive with a throttle body problem? Yes. But, the vehicle may be limited in power or put into what is referred to as limp mode, in order to get the vehicle to a repair facility. If the check engine light is on, or the electronic throttle control warning light is on, but there is no noticeable difference in engine performance, the car can be safely driven. However, it is best to have it diagnosed and repaired at your earliest convenience to avoid unexpected breakdown or possible damage to the catalytic converter.
Why would a throttle body go bad? One of the main causes of a malfunctioning throttle body is internal contamination. ... This causes 'false air' to be sucked in, so that the total amount of air sucked in does not correspond to the position of the throttle valve. An incorrectly adjusted throttle position sensor can also cause an engine to run badly.
Does throttle body need to be replaced? The throttle body plays a large role in controlling the fuel and air mixture in your engine. The proper mixture needs to be achieved in order for your engine to run smoothly and properly. Once this part fails, it needs replacing rather than repairing.
What happens if you don't replace a throttle body? When a throttle body is not functioning correctly, yourll usually notice a distinctly poor or very low idle. If the problem is really severe, you might even begin stalling when coming to a stop or when the throttle is quickly pressed.
Vehicle Compatibility Information Acura Integra 1.7L 1992-1993 Visa, and MasterCard are the accepted forms of payment.
Please use the eBay checkout system when paying for your order.
Immediate payment is required for all orders.
International orders will ship through eBay's Global Shipping Program. Please keep in mind that we are not responsible for any import duties or fees. All of our brand new items come with a 30-Days money-back guarantee. Any question, please contact us by email on working days. All rights reserved. |
||||||||||||||||||||||||||||||||||||||
- Brand: Turboshop
- Manufacturer Part Number: ECP16149301S
- Mounting Hardware Included: No
- Manufacturer Warranty: 1 Year
- Custom Bundle: No
- Fitment Type: Direct Replacement
- Material: Aluminum
- Color: Metal
- UPC: Does not apply
- OE Spec or Performance/Custom: Performance/Custom
- Items Included: 1 Fuel Injection Throttle Body
- Package Quantity: 1 Throttle Body
- Packaging Type: Box
- Interchange Part Number: 309-05-1050
- OE/OEM Part Number: 309051050
- Superseded Part Number: 309-051050
- Type: Throttle Body
- Placement on Vehicle: Front
- Features: Electronic
- Bore Diameter: 70mm
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $6.50 for the first item, $3.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–15 business days | $14.50 for the first item, $4.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
-
Email: support@ibspot.com
-
Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
-
The item must be unused, in the same condition as received, and in its original packaging.
-
A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
-
Perishable goods (for example, food, flowers, newspapers, magazines)
-
Intimate or sanitary goods
-
Hazardous materials or flammable liquids/gases
-
Gift cards
-
Downloadable software
-
Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
-
Books with obvious signs of use
-
Opened CDs, DVDs, software, or vinyl records
-
Items not in their original condition, damaged, or missing parts not due to our error
-
Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
-
In-store returns are refunded to the original form of payment or issued as a gift card.
-
Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
-
5–7 business days for the return to reach our Returns Center.
-
An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.